|
Mfg: Reed
Published: 2009
Version: Cat M 01002
80
pages
Reed Manufacturing has been producing fine tools for worldwide professional trades since its founding, in 1896, by Carl Reed. ... Five generations of Wrights have also provided a great place to work and exceptional contributions to the community. ... They assemble them and disassemble them in add...
Add to My Library
|
|
|
Mfg: Reed
Published: 2011
Version: 711-01071
6
pages
Reed's direct tapping machine is used to drill and tap water mains while under pressure, then to install 3/4'' or 1'' corporation stops in a 2-step operation. ... It covers a range of 4" - 48'' cast or ductile iron and C-900 PVC with the use of saddles and chain extensions. ... The TM1100 feature...
Add to My Library
|
|
|
Mfg: Reed
Published: 2010
Version: 01103-910
4
pages
CUTTER WHEELS ARE BETTER… ... Reed cutter wheels are made from high shock-resistant tool steel, while competitive wheels are made from carbon steel or still lower quality tool steel. ... By using this higher quality raw material, Reed cutter wheels can be made thinner and can therefore cut pipe m...
Add to My Library
|
|
|
Mfg: Reed
Published: 2011
Version: 411-01038
4
pages
“Flip Clamp” feed system is fast and easy-to-use; just flip the yoke to engage the boring bar. ... User friendly, low profile machines are lightweight and compact. ... Reed’s direct tapping machine is used to drill and tap water mains while under pressure, then to install 3/4’’ or 1’’ corporation s...
Add to My Library
|
|
|
Mfg: Reed
Published: 2010
Version: 310-01025
4
pages
Fastest way to get a square cut on steel pipe. ... After set-up, cuts can be done on 30” (760 mm) steel pipe in about 5 minutes. ... It takes about 1 minute per pipe diameter inch for set-up and cuts on ductile iron/cast iron. ... These pneumatic-powered units operate in trench, above ground or u...
Add to My Library
|
|
|
Mfg: Reed
Published: 2007
Version: 707-01078
2
pages
New "Flip Clamp" on star feed system is fast and easy-to-use; just flip the yoke to engage the boring bar. ... User friendly, low profile drilling machine that is lightweight (13.2 lbs/6 kg) and compact. ... DM1100 saddle taps ¾" to 1" while the DM2100 saddle taps ¾" to 2", both under pressure.
Add to My Library
|
|
|
Mfg: Reed
Published: 2009
Version: 709-01156
2
pages
Pressure test water systems such as water meters, plumbing lines, pressure vessels, solar systems and sprinkler systems, in both residential and commercial buildings. ... Hose features a quick disconnect with built-in check valve, which allows for convenient setup and portability. ... Smooth runn...
Add to My Library
|
|
|
Mfg: Reed
Published: 2011
Version: 611-01167
2
pages
needed for the job to give the tool maximum purpose. ... actual ... Reduce man hours spent looking for buried shut-off valves. ... Reduce waste of water or gas by enabling crews to get service restored quicker. ... PES6 and PES8 PE Squeeze-Off Tools compress polyethylene (PE) ... PE Squeeze-Off T...
Add to My Library
|
|
|
Mfg: Reed
Published: 2009
Version: 1109-01151-SE
2
pages
Reed PXCR and PEXOH crimpers squeeze the copper rings used on brass fittings, making PEX installation a breeze. ... The Reed design eliminates tool marks and distortion on the rings. ... For one-hand use consider the ... Each crimper features a go/no-go gauge. ... Close quarters PEXSD model utili...
Add to My Library
|
|
|
Mfg: Reed
Published: 2007
Version: 107-01128
2
pages
Use Rotary™ Cutters for 18" - 36" pipe. ... Cold cut large diameter steel, most stainless steel, ductile, and cast iron pipe in close quarters. ... The low profile design of the LCRC models needs only 4" clearance for up to 16" pipe diameter ... New star feed system with "flip clamp" is fast and ...
Add to My Library
|
|